- 432 - .129(3.27) .118(3.0) .012(.31) .006(.15) .008(.20) .004(.10) .060(1.52) .030(0.76) .245(6.22) .220(5.59) .280(7.11) .260(6.60) .103(2.62) .079(2.00) .320(8.13) .305(7.75) s5a thru s5m 5.0 amps. surface mount rectifiers voltage range 50 to 1000 volts current 5.0 amperes features for surface mounted application glass passivated junction chip. low forward voltage drop high current capability easy pick and place high surge current capability plastic material used carries underwriters laboratory classification 94v-o high temperature soldering: 260 o c / 10 seconds at terminals mechanical data case: molded plastic terminals: solder plated polarity: indicated by cathode band packaging: 16mm tape per eia std rs-481 weight: 0.21 gram smc/do-214ab dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol s5a s5b s5d s5g s5j S5K s5m units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current @t l =75 (note 1) i (av) 5.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 100 a maximum instantaneous forward voltage @ 5.0a v f 1.15 v maximum dc reverse current @ t a =25 at rated dc blocking volta g e @ t a =125 i r 10.0 250 ua ua typical thermal resistance (note 1) r jl r ja 13 47 /w typical junction capacitance ( note 2 ) cj 60 pf operating temperature range t j -55 to +150 storage temperature range t stg -55 to +150 notes: 1. measured on p.c. board with 0.6? x 0.6? (16mm x 16mm) copper pad areas. 2. measured at 1 mhz and applied v r =4.0 volts
- 433 - ratings and characteristic curves (s5a thru s5m) fig.4- typical reverse characteristics 0 20 40 60 80 100 120 140 .10 1.0 10 100 percent of rated peak reverse voltage. (%) tj=125 c 0 tj=25 c 0 fig.2- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 10 50 5 100 50 10 100 200 number of cycles at 60hz 8.3ms single half sine wave jedec method tj=tj max fig.3- typical forward characteristics instantaneous for ward current . (a) 1.4 1.6 0.6 0.7 .8 .9 1.0 1.2 0.01 0.03 0.1 0.3 1.0 3.0 10 100 30 forward voltage. (v) pulse width-300 s 2% duty cycle fig.5- typical junction capacitance junction cap acitance.(pf) 100 50 10 5 1 10 5 100 50 reverse voltage. (v) tj=25 c f=1.0mhz vsig=50mvp-p 0 tj=25 c 0 fig.1- maximum forward current derating curve average for ward current . (a) 50 60 70 80 100 110 120 130 140 90 150 0.5 3.0 7.0 6.0 5.0 4.0 1.0 2.0 lead temperature. ( c) o instantaneous reverse current .( a) resistive or inductive load p. c. board mounted on 16mm x 16mm pad areas
|
